Печать

Пожалуйста, войдите или зарегистрируйтесь.
1 час 1 день 1 неделя 1 месяц Навсегда

[kbm1]

Добрый день,
используем Тион-28 несколько лет, на большинстве плат все работает хорошо, но на некоторых проблемы такого рода: при включении часто мигает светодиод линк, пакеты на eth0 не идут. Если передернуть питание, иногда связь может появиться, и дальше плата будет работать. На одной плате такой проблемы изначально не было, но после нескольких дней работы она появилась, теперь линк на ней не поднимается совсем, а светодиод мигает даже при выдернутом кабеле. Также есть подозрения, что проблема чаще проявляется при повышенной температуре (порядка 40 град).
Накопилось около десятка таких плат.

[Danila]

Добрый день.

Уточните, Тион-28 или ТионПро-28?

[kbm1]

Тион28

[Danila]

Образ Linux используете наш или свой?

На схеме нашего Сириуса28 есть резисторы R38 и R101 номиналом 0 Ом. Проверьте, чтобы на Вашей плате номинал был такой-же. Раньше мы ставили 10 Ом.
Схема:
https://zao-zeo.ru/media/files/docs/sirius28_rev1.1_circuit.pdf

[kbm1]

Образ свой.

Замкнул резистор, ничего не дало.

Когда вы меняли с 10 Ом на ноль, у Вас как проблема проявлялась?

[Danila]

Долго устанавливалось соединение, с одной моделью роутеров вообще не устанавливалась связь.

Также мы обновляли драйвер ethernet. Патч прикрепил к письму.
в конфиге ядра нужно включить MX28_ENET_ISSUE после наложения патча.

[kbm1]

Под какое ядро Ваш патч? Мое 3.19.2 сильно отличается.
Думаю, будет проще залить Ваш образ для начала и проверить, поможет ли. Дайте сцылку. Может быть, у вас есть вариант, загружаемый с SD-карты?

[Danila]

Под 2.6.35.

Образ:
http://www.zao-zeo.ru/media/files/linux/2.6.35/tion-pro28_linux_20180321.zip

[kbm1]

Добрый день,

я взял Ваше ядро, скачал tion-pro28_rootfs_2018.03.21.tar, записал на карту в соответствии с Вашими инструкциями отсюда: https://www.zao-zeo.ru/dokuwiki/doku.php/tion-pro28#c_%D0%BE%D1%81_linux, env variables в u-boot задал и т.д.

Падение:

Код: [Выделить]

PowerPrep start initialize power...
Battery Voltage = 0.48V
No battery or bad battery                                       detected!!!.Disabling battery                                   voltage measurements./r/nApr 24 201311:42:00
FRAC 0x92925552
memory type is DDR2
Wait for ddr ready 1power 0x00820616
Frac 0x92925552
start change cpu freq
hbus 0x00000003
cpu 0x00010001
start test memory accress
ddr2 0x40000000
finish simple test


U-Boot 2009.08 (Sep 18 2015 - 11:31:04)

Freescale i.MX28 family
CPU:   454 MHz
BUS:   151 MHz
EMI:   205 MHz
GPMI:   24 MHz
DRAM:  128 MB
MMC:   IMX_SSP_MMC: 0, IMX_SSP_MMC: 1
In:    serial
Out:   serial
Err:   serial
Net:   got MAC address from IIM: 00:04:70:b3:d5:08
FEC0
Hit any key to stop autoboot:  0
reading uImage

2995848 bytes read
## Booting kernel from Legacy Image at 42000000 ...
   Image Name:   Linux-2.6.35.3-zeo-tion-pro28
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2995784 Bytes =  2.9 MB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.35.3-zeo-tion-pro28 (ubuntu@ubuntu) (gcc version 4.4.4 (4.4.4_09.06.2010) ) #77 PREEMPT Fri Aug 17 11:20:11 EDT 2018
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Freescale MX28EVK board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyAM0,115200n8 root=/dev/mmcblk0p1 rw rootwait
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 123268k/123268k available, 7804k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xfde00000 - 0xffe00000   (  32 MB)
    vmalloc : 0xc8800000 - 0xf0000000   ( 632 MB)
    lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc007f000   ( 476 kB)
      .text : 0xc007f000 - 0xc05f3000   (5584 kB)
      .data : 0xc05f4000 - 0xc0637480   ( 270 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
        RCU-based detection of stalled CPUs is disabled.
        Verbose stalled-CPUs detection is disabled.
NR_IRQS:288
Console: colour dummy device 80x30
console [ttyAM0] enabled
Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)
pid_max: default: 32768 minimum: 301
Security Framework initialized
SELinux:  Initializing.
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
regulator: vddd: 800 <--> 1575 mV at 1500 mV fast normal
regulator: vdddbo: 800 <--> 1575 mV fast normal
regulator: vdda: 1500 <--> 2275 mV at 1800 mV fast normal
vddio = 3280000, val=10
regulator: vddio: 2780 <--> 3680 mV at 3280 mV fast normal
regulator: overall_current: fast normal
regulator: vbus5v:
regulator: mxs-duart-1: fast normal
regulator: mxs-bl-1: fast normal
regulator: mxs-i2c-1: fast normal
regulator: mmc_ssp-1: fast normal
regulator: mmc_ssp-2: fast normal
regulator: charger-1: fast normal
regulator: power-test-1: fast normal
regulator: cpufreq-1: fast normal
i.MX IRAM pool: 120 KB@0xc8820000
Initializing GPMI pins
usb DR wakeup device is registered
IMX usb wakeup probe
audit: cannot initialize inotify handle
bio: create slab <bio-0> at 0
SCSI subsystem initialized
Freescale USB OTG Driver loaded, $Revision: 1.55 $
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource mxs clock source
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registered
mxs_cpu_init: cpufreq init finished
audit: initializing netlink socket (disabled)
type=2000 audit(0.600:1): initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) A© 2001-2006 Red Hat, Inc.
msgmni has been set to 240
alg: No test for stdrng (krng)
cryptodev: driver loaded.
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Console: switching to colour frame buffer device 80x60
mxs-duart.0: ttyAM0 at MMIO 0x80074000 (irq = 47) is a DebugUART
UART set mode; UART - 0, mode - 0

mxs-auart.0: ttySP0 at MMIO 0x8006a000 (irq = 112) is a mxs-auart.0
Found APPUART 3.1.0 (DMA)
UART set mode; UART - 1, mode - 0

mxs-auart.1: ttySP1 at MMIO 0x8006c000 (irq = 113) is a mxs-auart.1
Found APPUART 3.1.0 (DMA)
UART set mode; UART - 2, mode - 0

mxs-auart.2: ttySP2 at MMIO 0x8006e000 (irq = 114) is a mxs-auart.2
Found APPUART 3.1.0 (DMA)
UART set mode; UART - 3, mode - 0

mxs-auart.3: ttySP3 at MMIO 0x80070000 (irq = 115) is a mxs-auart.3
Found APPUART 3.1.0 (DMA)
UART set mode; UART - 4, mode - 0

mxs-auart.4: ttySP4 at MMIO 0x80072000 (irq = 116) is a mxs-auart.4
Found APPUART 3.1.0 (DMA)
brd: module loaded
loop: module loaded
i.MX GPMI NFC
NFC: Version 1, 8-chip GPMI and BCH
Boot ROM: Version 1, Single-chip boot area, block mark swapping supported
Scanning for NAND Flash chips...
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 1 at 0x000000020000
Bad eraseblock 2 at 0x000000040000
Bad eraseblock 3 at 0x000000060000
Boot area protection is enabled.
Creating 2 MTD partitions on "gpmi-nfc-main":
0x000000000000-0x000001400000 : "gpmi-nfc-0-boot"
0x000001400000-0x000010000000 : "gpmi-nfc-general-use"
mxs-spi mxs-spi.0: Max possible speed 24000 = 24000000/2 kHz
mxs-spi mxs-spi.0: at 0x80014000 mapped to 0xF0014000, irq=84, bus 1, DMA ver_major 4
Freescale FlexCAN Driver
FEC Ethernet Driver
fec_enet_mii_bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci: irq 93, io base 0x80080000
fsl-ehci fsl-ehci: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Freescale On-Chip EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.35.3-zeo-tion-pro28 ehci_hcd
usb usb1: SerialNumber: fsl-ehci
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 2
fsl-ehci fsl-ehci.0: irq 92, io base 0x80090000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: Freescale On-Chip EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.35.3-zeo-tion-pro28 ehci_hcd
usb usb2: SerialNumber: fsl-ehci.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ARC USBOTG Device Controller driver (1 August 2005)
mice: PS/2 mouse device common for all mice
input: MXS touchscreen as /devices/virtual/input/input0
rtc-ds1307 0-0068: rtc core: registered m41t00 as rtc0
i2c /dev entries driver
IR NEC protocol handler initialized
IR RC5(x) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
Linux video capture interface: v2.00
WARNING : No battery connected !

Aborting power driver initialization
mxs-battery: probe of mxs-battery.0 failed with error 1
mxs watchdog: initialized, heartbeat 19 sec
mxs-mmc: MXS SSP Controller MMC Interface driver
mxs-mmc mxs-mmc.0: mmc0: MXS SSP MMC DMAIRQ 82 ERRIRQ 96
dcp dcp.0: DCP crypto enabled.!
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1926 buckets, 7704 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
mmc0: new high speed SDHC card at address 0007
mmcblk0: mmc0:0007 SD16G 14.4 GiB
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
can: controller area network core (rev 20090105 abi 8)
NET: Registered protocol family 29
 mmcblk0: p1 p2 p3
regulator_init_complete: incomplete constraints, leaving vbus5v on
rtc-ds1307 0-0068: setting system clock to 2018-08-24 10:05:30 UTC (1535105130)
VFS: Mounted root (vfat filesystem) on device 179:1.
Freeing init memory: 476K
Kernel panic - not syncing: No init found.  Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
Backtrace:
[<c00835b0>] (dump_backtrace+0x0/0x10c) from [<c04ad654>] (dump_stack+0x18/0x1c)
 r7:00000013 r6:c00a0118 r5:c002db30 r4:c0638398
[<c04ad63c>] (dump_stack+0x0/0x1c) from [<c04ad6d0>] (panic+0x78/0xf8)
[<c04ad658>] (panic+0x0/0xf8) from [<c007f608>] (init_post+0x90/0xe4)
 r3:00000000 r2:c7d78700 r1:c7d78800 r0:c056b758
[<c007f578>] (init_post+0x0/0xe4) from [<c00084fc>] (kernel_init+0x12c/0x170)
 r5:c002db30 r4:c0637500
[<c00083d0>] (kernel_init+0x0/0x170) from [<c00a0118>] (do_exit+0x0/0x718)
 r5:c00083d0 r4:00000000



[Danila]

Похоже, что КФС записана не правильно.
Попробуйте записать во флешь через mfgtool.

[kbm1]

Я пробовал записать через проводник, как в инструкции, попробовал и из-под Linux. Перезаписал несколько раз.
На нашей плате USB порты заняты, под mfgtool подключиться не смогу.
Вы можете образ карточки выложить?

[Danila]

Образ:

https://drive.google.com/file/d/1cs-C86rLNwQLio_W4SsUrsjaragZGInH/view?usp=sharing

[kbm1]

PHY сбрасывается через каждые несколько секунд. Несмотря на строку PHY: 0:00 - Link is Up - 100/Full связи все равно нет.

Код: [Выделить]

PowerPrep start initialize power...
Battery Voltage = 1.95V
No battery or bad battery                                       detected!!!.Disabling battery                                       voltage measurements./r/nMay 22 201808:18:22
FRAC 0x92925552
memory type is DDR2
Wait for ddr ready 1power 0x00820710
Frac 0x92925552
start change cpu freq
hbus 0x00000003
cpu 0x00010001


U-Boot 2009.08 (Sep 18 2015 - 11:31:04)

Freescale i.MX28 family
CPU:   454 MHz
BUS:   151 MHz
EMI:   205 MHz
GPMI:   24 MHz
DRAM:  128 MB
MMC:   IMX_SSP_MMC: 0, IMX_SSP_MMC: 1
In:    serial
Out:   serial
Err:   serial
Net:   got MAC address from IIM: 00:04:70:b3:d5:08
FEC0
Hit any key to stop autoboot:  0

MMC read: dev # 0, block # 256,count 12288 ...
12288 blocks read: OK
## Booting kernel from Legacy Image at 42000000 ...
   Image Name:   Linux-2.6.35.3-zeo-tion-pro28
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2995784 Bytes =  2.9 MB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.35.3-zeo-tion-pro28 (ubuntu@ubuntu) (gcc version 4.4.4 (4.4.4_09.06.2010) ) #77 PREEMPT Fri Aug 17 11:20:11 EDT 2018
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Freescale MX28EVK board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyAM0,115200n8 noinitrd root=/dev/mmcblk0p3 rw rootwait
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 123268k/123268k available, 7804k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xfde00000 - 0xffe00000   (  32 MB)
    vmalloc : 0xc8800000 - 0xf0000000   ( 632 MB)
    lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc007f000   ( 476 kB)
      .text : 0xc007f000 - 0xc05f3000   (5584 kB)
      .data : 0xc05f4000 - 0xc0637480   ( 270 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
        RCU-based detection of stalled CPUs is disabled.
        Verbose stalled-CPUs detection is disabled.
NR_IRQS:288
Console: colour dummy device 80x30
console [ttyAM0] enabled
Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)
pid_max: default: 32768 minimum: 301
Security Framework initialized
SELinux:  Initializing.
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
regulator: vddd: 800 <--> 1575 mV at 1500 mV fast normal
regulator: vdddbo: 800 <--> 1575 mV fast normal
regulator: vdda: 1500 <--> 2275 mV at 1800 mV fast normal
vddio = 3280000, val=10
regulator: vddio: 2780 <--> 3680 mV at 3280 mV fast normal
regulator: overall_current: fast normal
regulator: vbus5v:
regulator: mxs-duart-1: fast normal
regulator: mxs-bl-1: fast normal
regulator: mxs-i2c-1: fast normal
regulator: mmc_ssp-1: fast normal
regulator: mmc_ssp-2: fast normal
regulator: charger-1: fast normal
regulator: power-test-1: fast normal
regulator: cpufreq-1: fast normal
i.MX IRAM pool: 120 KB@0xc8820000
Initializing GPMI pins
usb DR wakeup device is registered
IMX usb wakeup probe
audit: cannot initialize inotify handle
bio: create slab <bio-0> at 0
SCSI subsystem initialized
Freescale USB OTG Driver loaded, $Revision: 1.55 $
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource mxs clock source
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registered
mxs_cpu_init: cpufreq init finished
audit: initializing netlink socket (disabled)
type=2000 audit(0.600:1): initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) A© 2001-2006 Red Hat, Inc.
msgmni has been set to 240
alg: No test for stdrng (krng)
cryptodev: driver loaded.
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Console: switching to colour frame buffer device 80x60
mxs-duart.0: ttyAM0 at MMIO 0x80074000 (irq = 47) is a DebugUART
UART set mode; UART - 0, mode - 0

mxs-auart.0: ttySP0 at MMIO 0x8006a000 (irq = 112) is a mxs-auart.0
Found APPUART 3.1.0 (DMA)
UART set mode; UART - 1, mode - 0

mxs-auart.1: ttySP1 at MMIO 0x8006c000 (irq = 113) is a mxs-auart.1
Found APPUART 3.1.0 (DMA)
UART set mode; UART - 2, mode - 0

mxs-auart.2: ttySP2 at MMIO 0x8006e000 (irq = 114) is a mxs-auart.2
Found APPUART 3.1.0 (DMA)
UART set mode; UART - 3, mode - 0

mxs-auart.3: ttySP3 at MMIO 0x80070000 (irq = 115) is a mxs-auart.3
Found APPUART 3.1.0 (DMA)
UART set mode; UART - 4, mode - 0

mxs-auart.4: ttySP4 at MMIO 0x80072000 (irq = 116) is a mxs-auart.4
Found APPUART 3.1.0 (DMA)
brd: module loaded
loop: module loaded
i.MX GPMI NFC
NFC: Version 1, 8-chip GPMI and BCH
Boot ROM: Version 1, Single-chip boot area, block mark swapping supported
Scanning for NAND Flash chips...
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 1 at 0x000000020000
Bad eraseblock 2 at 0x000000040000
Bad eraseblock 3 at 0x000000060000
Boot area protection is enabled.
Creating 2 MTD partitions on "gpmi-nfc-main":
0x000000000000-0x000001400000 : "gpmi-nfc-0-boot"
0x000001400000-0x000010000000 : "gpmi-nfc-general-use"
mxs-spi mxs-spi.0: Max possible speed 24000 = 24000000/2 kHz
mxs-spi mxs-spi.0: at 0x80014000 mapped to 0xF0014000, irq=84, bus 1, DMA ver_major 4
Freescale FlexCAN Driver
FEC Ethernet Driver
fec_enet_mii_bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci: irq 93, io base 0x80080000
fsl-ehci fsl-ehci: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Freescale On-Chip EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.35.3-zeo-tion-pro28 ehci_hcd
usb usb1: SerialNumber: fsl-ehci
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 2
fsl-ehci fsl-ehci.0: irq 92, io base 0x80090000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: Freescale On-Chip EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.35.3-zeo-tion-pro28 ehci_hcd
usb usb2: SerialNumber: fsl-ehci.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ARC USBOTG Device Controller driver (1 August 2005)
mice: PS/2 mouse device common for all mice
input: MXS touchscreen as /devices/virtual/input/input0
rtc-ds1307 0-0068: rtc core: registered m41t00 as rtc0
i2c /dev entries driver
IR NEC protocol handler initialized
IR RC5(x) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
Linux video capture interface: v2.00
WARNING : No battery connected !

Aborting power driver initialization
mxs-battery: probe of mxs-battery.0 failed with error 1
mxs watchdog: initialized, heartbeat 19 sec
mxs-mmc: MXS SSP Controller MMC Interface driver
mxs-mmc mxs-mmc.0: mmc0: MXS SSP MMC DMAIRQ 82 ERRIRQ 96
dcp dcp.0: DCP crypto enabled.!
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1926 buckets, 7704 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
mmc0: new high speed SDHC card at address 0007
mmcblk0: mmc0:0007 SD16G 14.4 GiB
 mmcblk0:
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
can: controller area network core (rev 20090105 abi 8)
NET: Registered protocol family 29
 p1 p2 p3
regulator_init_complete: incomplete constraints, leaving vbus5v on
rtc-ds1307 0-0068: setting system clock to 2018-09-04 11:40:11 UTC (1536061211)
EXT2-fs (mmcblk0p3): warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem) on device 179:3.
Freeing init memory: 476K

init started: BusyBox v1.15.0 ()

starting pid 759, tty '': '/etc/rc.d/rcS'
Mounting /proc and /sys
Running sysctl
Setting up networking on loopback device:
Setting up networking on eth0:
eth0: Freescale FEC PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=0:00, irq=-1)
Adding static route for default gateway to 192.168.1.1:
Setting nameserver to 192.168.1.1 in /etc/resolv.conf:
Starting inetd:
Starting the hotplug events dispatcher udevd
Synthesizing initial hotplug events
PHY: 0:00 - Link is Up - 100/Full
Setting the hostname to freescale
Mounting filesystems
Resetting PHY
EXT2-fs (mmcblk0p3): error: ext2_lookup: deleted inode referenced: 29075
EXT2-fs (mmcblk0p3): error: ext2_lookup: deleted inode referenced: 29075
EXT2-fs (mmcblk0p3): error: ext2_lookup: deleted inode referenced: 29075
ln: /etc/mtab: Input/output error
EXT2-fs (mmcblk0p3): error: ext2_lookup: deleted inode referenced: 29075
EXT2-fs (mmcblk0p3): error: ext2_lookup: deleted inode referenced: 29075
mount: can't open /etc/mtab for writing: Input/output error
Starting the port mapper:
Starting the ssh server:
Starting the watchdog daemon:
EXT2-fs (mmcblk0p3): error: ext2_free_blocks: bit already cleared for block 217088
sh: start: unknown operand

starting pid 1333, tty '': '/sbin/getty -L ttyAM0 115200 vt100'


arm-none-linux-gnueabi-gcc (4.4.4_09.06.2010) 4.4.4

root filesystem built on Fri, 02 Oct 2015 12:16:03 -0400

Freescale Semiconductor, Inc.



freescale login: Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY
PHY: 0:00 - Link is Down
PHY: 0:00 - Link is Up - 100/Full
Resetting PHY
PHY: 0:00 - Link is Up - 100/Full
Resetting PHY
PHY: 0:00 - Link is Up - 100/Full
Resetting PHY
Resetting PHY
Resetting PHY
Resetting PHY


arm-none-linux-gnueabi-gcc (4.4.4_09.06.2010) 4.4.4

root filesystem built on Fri, 02 Oct 2015 12:16:03 -0400

Freescale Semiconductor, Inc.



freescale login: root
login[1333]: root login on 'ttyAM0'



BusyBox v1.15.0 () built-in shell (ash)
Enter 'help' for a list of built-in commands.

root@freescale ~$ ls
SP1          minicom.log
root@freescale ~$ Resetting PHY
mc
-sh: mc: not found
root@freescale ~$ ifcResetting PHY
onfig
eth0      Link encap:Ethernet  HWaddr 70:B3:D5:08:32:98
          inet addr:192.168.1.28  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:468 (468.0 b)
          Base address:0x8000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

root@freescale ~$ Resetting PHY
Resetting PHY
PHY: 0:00 - Link is Down
PHY: 0:00 - Link is Up - 100/Full



[Danila]

Привозите, посмотрим.

[kbm1]

У вас делается аппаратный сброс phy ножкой GPIO4_13. Добавил у себя однократный сброс при загрузке системы. На данный момент проблему можно считать решенной, из 15 отбракованных плат работают все, кроме двух.
Одна из этих двух - та, про которую я тут писал, не запустилась ни с вашим, ни с моим образом, вторая, по всей видимости, с непропаем, при нажатии на нее на нашей плате подмаргивают светодиоды. Эти две платы отправим к вам, как будет возможность.
Кстати, у вас на схеме rev1.1 ошибка, ножка ENET0_RX_CLK/GPIO4_13 обозначена как ENET0_RX_CLK/GPIO4_1.